Three Services, Each Done with Attention
Water pressure checks, drain clearing, and basin replacements — the three most common home plumbing needs in Kuala Lumpur, handled in full from first visit to final test.
Back to HomeHow AirJaya Approaches Every Job
The same process applies whether we are checking a tap or replacing a basin — thoroughness at each step prevents the need for a return visit.
1. Book
Call or send a message. Booking confirmed the same business day with a two-hour arrival window.
2. Inspect
Technician walks through the issue, checks the pipe type and fitting condition, and shares findings before any work begins.
3. Work
With your agreement on scope and cost, the job is carried out using pipe-matched tools and standard replacement parts from the van.
4. Test & Hand Over
Hot and cold sides run through a full cycle. Site is cleaned. Technician signs off only when everything holds.
Water Pressure & Tap Check
A neighbourly visit to inspect main inlet pressure, check kitchen and bathroom taps, and look at the household's flow at different points. The technician notes any signs of partial blockage or aging connectors and shares findings in plain language. Small adjustments and washer changes are handled on the spot.
What Is Included
- Main inlet valve pressure reading
- Kitchen and bathroom tap flow inspection
- Connector and washer condition check
- On-the-spot washer replacement if needed
- Verbal summary of findings
Process steps:
Isolate and read main inlet pressure at valve
Check each tap for flow rate and drip
Inspect visible connectors for wear
Replace worn washers and adjust fittings
Run all taps and confirm steady flow
Bathroom Drain Unclogging
Clearing of bathroom basins, shower traps, and toilet drains that have slowed or stopped. Tools are chosen to suit the type of pipe so the work is gentle on existing fittings. The technician confirms a full drain cycle before leaving.
What Is Included
- Basin, shower trap, and toilet drain assessment
- Pipe-type matched clearing method
- Trap removal and cleaning if accessible
- Full drain cycle confirmation
- Work area cleaned on completion
Process steps:
Identify affected drains and note pipe type
Select appropriate clearing tool
Clear blockage without stressing fittings
Flush and time full drain cycle
Clean area and confirm with homeowner
Washbasin & Sink Replacement
Removal of an existing basin or sink and fitting of a new unit. Includes new tap mounting where needed, fresh sealant work along the counter or wall, and pipe alignment for a steady drain. Final water test on hot and cold sides is included.
What Is Included
- Old unit removed and carried away
- New basin or sink seated and secured
- Tap mounted and supply connected
- Fresh sealant bead along counter/wall joint
- Hot and cold water final test
Process steps:
Isolate water supply and remove old basin
Prepare mounting surface and align pipe stub
Seat and secure new basin; mount tap
Apply sealant bead and connect supply lines
Run hot and cold test; check all joints
Which Service Do You Need?
Use the table below to narrow down the right visit for your situation.
| Your Situation | Pressure & Tap RM 245 |
Drain Clearing RM 310 |
Basin Replace RM 1,260 |
|---|---|---|---|
| Low water pressure from taps | — | — | |
| Tap dripping when closed | — | — | |
| Shower or basin draining slowly | — | — | |
| Toilet drain backing up | — | — | |
| Basin cracked or needs upgrade | — | — | |
| Kitchen sink replacement | — | — |
Technical Standards Across All Services
SPAN Compliance
All pipe work and fittings meet Suruhanjaya Perkhidmatan Air Negara standards for domestic installations in Malaysia.
Supply Isolated Before Work
Water supply is always isolated at the relevant valve before any fitting or pipe is touched — a basic safety step not always followed.
Post-Work Flow Test
Every job ends with a timed flow run on all affected sides — not a visual check alone — before the technician signs off.
Site Tidied on Departure
Off-cuts, packaging, and debris are cleared. Surfaces within the work area are wiped before the technician leaves.
Itemised Invoice
Labour, consumables, and any additional parts listed separately. No bundled totals — every line is explained if requested.
Findings Shared During Work
Any additional issues noted mid-visit are reported immediately. Extra work only proceeds with the homeowner's clear agreement.
Pricing at a Glance
All prices in Malaysian Ringgit. Standard consumables included. Additional parts quoted separately before purchase.
Pressure & Tap
Per visit
RM 245- Inlet pressure reading
- All taps inspected
- Washer replacements included
- Verbal report
Drain Clearing
Per visit
RM 310- Basin, shower & toilet drains
- Pipe-safe clearing method
- Full drain cycle test
- Work area cleaned
Basin Replacement
Per fitting
RM 1,260- Old unit removed
- New basin fitted & sealed
- Tap mounted
- Hot & cold water tested
Basin/sink unit cost not included. Parts beyond standard consumables quoted before purchase. Call for a pre-visit estimate.
Not Sure Which Service Fits?
Call us and describe the problem — we will point you to the right visit or suggest a combined check if multiple issues are involved.